chop saw stand
Moderators: HopefulSSer, admin
chop saw stand
On Doug Reid's web site he has a couple of pics of a stand he made to use a ryobi chop saw on the SS. Though there was talk of him producing plans for this, I haven't seen any. Does anybody have plans for this?
I don't see any plans posted but it shouldn't be too hard to make you own.
The third photo down on this page shows good detail of the construction.
I will reproduce it here for ease of reference
[ATTACH]25275[/ATTACH]
The top of the stand needs to be a bit larger than the base of you chop saw.
The sides need to be inset enough that they don't interfere with the with the chop saw mounting bolts.
The height needs to be such that the table of the chop saw is a bit higher than the top of the ShopSmith headstock so that the ShopSmith main and auxiliary tables can be used to support the wood being cut.
A different approach to this is shown on this post
The third photo down on this page shows good detail of the construction.
I will reproduce it here for ease of reference
[ATTACH]25275[/ATTACH]
The top of the stand needs to be a bit larger than the base of you chop saw.
The sides need to be inset enough that they don't interfere with the with the chop saw mounting bolts.
The height needs to be such that the table of the chop saw is a bit higher than the top of the ShopSmith headstock so that the ShopSmith main and auxiliary tables can be used to support the wood being cut.
A different approach to this is shown on this post
- Attachments
-
- chopsawstand.jpg (123.11 KiB) Viewed 9922 times
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
re chop saw stand
Thanks, i had never seen the second one. I'll get to work.
I just clamp my compound miter circular saw directly to the table on my "500" from the back. Then I can slide it back and forth to set-up the support I need on either side with the extension tables. And I can adjust the height of the table (within reason) to match the adjustable height of the extension tables. Other than "F" clamps, nothing else special is needed.
________________________________________________________________________________________________
1981 Mark V 500, bandsaw, belt sander, jig saw, jointer; contractor's table saw; multiple circular saws and miter saws; and a trailer full of tools.
"It is better to remain silent and thought a fool than to speak out and remove all doubt"
Abraham Lincoln
1981 Mark V 500, bandsaw, belt sander, jig saw, jointer; contractor's table saw; multiple circular saws and miter saws; and a trailer full of tools.
"It is better to remain silent and thought a fool than to speak out and remove all doubt"
Abraham Lincoln
Thanks for bringing it to our attention. Please post pictures when you are done.JonE wrote:Thanks, i had never seen the second one. I'll get to work.
I may make one myself, the stand I have for my sliding compound miter saw takes up way to much floor space.
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
It seems like an option that utilizes the SS main table would be preferred, as it gives you the easy ability to raise/lower etc. as needed. Matter of fact, the suggestion of just clamping it to the main table seems the simplest - has anyone tried this and had troubles with it slipping or otherwise have problems that would make some sort of mount more suitable?
'78 Mark V 500 #27995 (my Dad bought new)
'82 Mark V 500 #96309
Two '47 10E's (serial#4314+6149) - one a dedicated drill press and the other a lathe
Two 10E/ER in parts slowly being restored…#26822 and #????? (SS plate missing)
SPT's: Bandsaw, Belt Sander, Strip Sander, Jointer, Jigsaw, Biscuit Joiner
'82 Mark V 500 #96309
Two '47 10E's (serial#4314+6149) - one a dedicated drill press and the other a lathe
Two 10E/ER in parts slowly being restored…#26822 and #????? (SS plate missing)
SPT's: Bandsaw, Belt Sander, Strip Sander, Jointer, Jigsaw, Biscuit Joiner
See post #4. I've used clamps for years without a single problem. My scms is mounted on a piece of MDO the same size as the "500" table.dgale wrote:It seems like an option that utilizes the SS main table would be preferred, as it gives you the easy ability to raise/lower etc. as needed. Matter of fact, the suggestion of just clamping it to the main table seems the simplest - has anyone tried this and had troubles with it slipping or otherwise have problems that would make some sort of mount more suitable?
________________________________________________________________________________________________
1981 Mark V 500, bandsaw, belt sander, jig saw, jointer; contractor's table saw; multiple circular saws and miter saws; and a trailer full of tools.
"It is better to remain silent and thought a fool than to speak out and remove all doubt"
Abraham Lincoln
1981 Mark V 500, bandsaw, belt sander, jig saw, jointer; contractor's table saw; multiple circular saws and miter saws; and a trailer full of tools.
"It is better to remain silent and thought a fool than to speak out and remove all doubt"
Abraham Lincoln