Shopsmith Forums -- Sharing Information About Woodworking and Shopsmith Tools

info@shopsmith.com

(937) 890-5197

Shopsmith Forums

%nbsp;

Forum Home Page ‹ Main Woodworking Forum ‹ General Woodworking

It is currently Sun Dec 15, 2019 7:28 pm

• FAQ • Print view • Register • Login

10ER Double Tilt idea

14 posts Previous 1 2

Re: 10ER Double Tilt idea

#258771 by rpd » Tue Apr 09, 2019 9:36 am

rpd">

rpd Platinum Member (2152 Posts)
Location: Victoria, B.C.

This has come up before.

https://www.shopsmith.com/ss_forum/maintenance-and-repair-f10/double-tilt-10er--t21075.html#p245470

I think your base should work fine. For the left tilt position the table will need to be modified. It won't pivot 90 deg in that direction, and reversing it in the carriage results in the tie bar interfering with the spindle. There are pictures in the thread above that I copied from the yahoo group that show a table modification/solution.

---

Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,

Post a reply Reply with quote

Re: 10ER Double Tilt idea

#258904 by larryhrockisland » Tue Apr 16, 2019 8:14 pm

larryhrockisland Gold Member (79 Posts)

rpd wrote:This has come up before.

https://www.shopsmith.com/ss_forum/maintenance-and-repair-f10/double-tilt-10er--t21075.html#p245470

I think your base should work fine. For the left tilt position the table will need to be modified. It won't pivot 90 deg in that direction, and reversing it in the carriage results in the tie bar interfering with the spindle. There are pictures in the thread above that I copied from the yahoo group that show a table modification/solution.

Thanks, I didn't remember seeing that one. I came up with a table using my old craftsman router table, parts from my 510 to 520 upgrade, aluminum angle from my brother and 1" tubes from old store fixtures.

Attachments

: IMG_0243A.jpg (165.05 KiB) Viewed 5172 times

: Imagine this one rotated 180 for shaping; IMG_0244A.JPG (209.01 KiB) Viewed 5172 times

: As a router table, maybe pin routing; IMG_0254A.JPG (177.76 KiB) Viewed 5172 times

: With support legs which I would use in the shaper setup too; IMG_0255A.JPG (175.03 KiB) Viewed 5172 times

---

Larry Hargrove
Rock Island, Ok
1981 Mark V 500>510>520(98922)
19?? Mark V 500>Power Pro headstock 556176 06-17-11 factory exchange program original serial unknown
1957 Mark V 500 (350389)
1953 10ER
Another 10ER
Bandsaw 2012 Jointer 2012
Bandsaw, Jointer, other goodies
Craftsman table saw, Delta 46-460 Midi lathe

Post a reply Reply with quote

Re: 10ER Double Tilt idea

#258908 by JPG » Tue Apr 16, 2019 11:35 pm

JPG">

JPG Platinum Member (30040 Posts)
WLM: JPG40504@YAHOO.COM Location: Lexington, Ky (WILDCAT territory)

Oh I DO like folks who's brains wander outside the box!!!!

---

╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E(SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange

Post a reply Reply with quote