Shopsmith Forums

10E ad says to make an offer. Wish I lived closer.

https://chicago.craigslist.org/nwc/tls/ ... 50173.html

Price has dropped from $600 OBO to $350 OBO

https://sandiego.craigslist.org/nsd/tls ... 57284.html

On Ebay!
4E Jointer, Henge Plate and Headrest by the same seller.
I might have posted this in the wrong place earlier.
Dave V.

https://www.ebay.com/itm/Shopsmith-10er ... 1438.l2649

https://www.ebay.com/itm/Shopsmith-10er ... 1438.l2649

https://www.ebay.com/itm/Shopsmith-10er ... 1438.l2649

csxeng wrote:On Ebay!
4E Jointer, Henge Plate and Headrest by the same seller.
I might have posted this in the wrong place earlier.
Dave V.

https://www.ebay.com/itm/Shopsmith-10er ... 1438.l2649

https://www.ebay.com/itm/Shopsmith-10er ... 1438.l2649

https://www.ebay.com/itm/Shopsmith-10er ... 1438.l2649

I saw that and am watching to see what it goes for, though I don't need another. There is also a motor pulley adapter for it by another seller I think, but it doesn't have the large pulley on it.

There's also a complete ER with the same jointer, and everything looks intact, $550 obo.

Sent from my Moto Z3 Play using Tapatalk

[quote="badtheba"][quote="csxeng"]On Ebay!
4E Jointer, Henge Plate and Headrest by the same seller.
I might have posted this in the wrong place earlier.
Dave V.

https://www.ebay.com/itm/Shopsmith-10er ... d=38.l2649

https://www.ebay.com/itm/Shopsmith-10er ... 1438.l2649

M. There is also a motor pulley adapter for it by another seller I think, but it doesn't have the large pulley on it.

There's also a complete ER with the same jointer, and everything looks intact, $550 obo.

csxeng wrote:

badtheba wrote:

csxeng wrote:On Ebay!
4E Jointer, Henge Plate and Headrest by the same seller.
I might have posted this in the wrong place earlier.
Dave V.

https://www.ebay.com/itm/Shopsmith-10er ... d=38.l2649

https://www.ebay.com/itm/Shopsmith-10er ... 1438.l2649

M. There is also a motor pulley adapter for it by another seller I think, but it doesn't have the large pulley on it.

There's also a complete ER with the same jointer, and everything looks intact, $550 obo.

Where’s this at!!??

csxeng wrote:

csxeng wrote:

badtheba wrote:

Where’s this at!!??

I posted it here a week or so ago.

https://rover.ebay.com/rover/0/0/0?mpre ... 3558762325

Sent from my Moto Z3 Play using Tapatalk

And here's the pulley motor shaft adapter. I've already asked them about a sleeve/bushing to go to a smaller motor shaft size and they said the I.D. is 3/4 with no other sleeve that came with it. I'll have to measure mine sometime, but I got every single piece I needed when I got it on a Craigslist 10ER. I'm not looking to buy, I just try to keep up on what they go for.

https://rover.ebay.com/rover/0/0/0?mpre ... 2771410310

Sent from my Moto Z3 Play using Tapatalk

Bad,
I had to buy a new reducer sleeve for mine cause I lose the original one. My motor is 5/8 shaft. They are available off ebay. Without the sleeve the motor extension will fit right on the 3/4 motor shaft.

By the way, Killer job on the ER. The two tone colors look great! Keep up the good work!
Dave V.

csxeng wrote:Bad,
I had to buy a new reducer sleeve for mine cause I lose the original one. My motor is 5/8 shaft. They are available off ebay. Without the sleeve the motor extension will fit right on the 3/4 motor shaft.

By the way, Killer job on the ER. The two tone colors look great! Keep up the good work!
Dave V.

Thanks! My eventual plan is to have that first one set up primarily in horizontal with variable speed DC motor, my second one as a weird double tilt, and the third one as a drill press. Now I'm in the market for a Mark V with an upgraded fence to use as a table saw and get a band saw for that. Why can't spring get here already so I can put concrete in my tiny shop?!

Sent from my Moto Z3 Play using Tapatalk