Finish for woodworking jigs & fixtures?
Moderators: HopefulSSer, admin
- BuckeyeDennis
- Platinum Member
- Posts: 3698
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Finish for woodworking jigs & fixtures?
Hey guys, I'm building an exact-fit dado jig, similar to this one by Marc Spagnuolo, The Wood Whisperer.
[youtube]https://www.youtube.com/watch?time_cont ... j4vGS4HY-8[/youtube]
My materials are 3/4" baltic birch plywood, and some solid oak edging for the fences where the router bushing rides. I don't normally put a finish on shop-made jigs. But it's a bit of work getting good straight edges on the fences of this jig, and so I'm inclined to apply some sort of protective finish.
Any recommendations?
[youtube]https://www.youtube.com/watch?time_cont ... j4vGS4HY-8[/youtube]
My materials are 3/4" baltic birch plywood, and some solid oak edging for the fences where the router bushing rides. I don't normally put a finish on shop-made jigs. But it's a bit of work getting good straight edges on the fences of this jig, and so I'm inclined to apply some sort of protective finish.
Any recommendations?
- twistsol
- Gold Member
- Posts: 225
- Joined: Mon Feb 22, 2016 9:35 pm
- Location: Cottage Grove, MN
- Contact:
Re: Finish for woodworking jigs & fixtures?
I use tung oil (boiled linseed oil) on all my shop jigs. It is cheap, easy to apply and easy to refresh as it it wears off.
Thanks much,
Chris Phelps
Cheap tools are too expensive
2x Mark 5 520 and a 10ER
Chris Phelps
Cheap tools are too expensive
2x Mark 5 520 and a 10ER
Re: Finish for woodworking jigs & fixtures?
I use Watco or Waterlox oils. Very easy to apply and renew.
Re: Finish for woodworking jigs & fixtures?
I don't use any finish on my jigs. But, I don't make any critical fit jigs from plywood. I use maple hardwood. With just a bit of sanding on the edges, maple gives a crisp sharp edge.
- ChrisNeilan
- Platinum Member
- Posts: 1461
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Re: Finish for woodworking jigs & fixtures?
I use whatever is on hand, but wipe on poly is easiest for me. It also helps seal the wood from moisture so wood movement is lessened.
Chris Neilan
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
-
- Platinum Member
- Posts: 1564
- Joined: Wed Feb 05, 2014 11:57 am
- Location: Las Vegas NV
Re: Finish for woodworking jigs & fixtures?
I use Watco when I do seal them but most of the time I just leave them bare.
Paul
Paul
- BuckeyeDennis
- Platinum Member
- Posts: 3698
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: Finish for woodworking jigs & fixtures?
Sehast mentioned Watco as well. Are you guys talking about their "Danish Oil" products? I see that the Watco brand includes a bunch of different products, including tung oil and wipe-on poly.masonsailor2 wrote:I use Watco when I do seal them but most of the time I just leave them bare.
Paul
https://www.rustoleum.com/product-catal ... nds/watco/
- robinson46176
- Platinum Member
- Posts: 4182
- Joined: Mon Mar 09, 2009 9:00 pm
- Location: Central Indiana (Shelbyville)
Re: Finish for woodworking jigs & fixtures?
I keep a couple of cans of spray shellac and on something nice I use that so it stays clean. I have also been known to paint some items thinly to seal it. Most are left plain and they don't really matter much since such things tend to sink out of sight and vanish anyway...
.
.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
Re: Finish for woodworking jigs & fixtures?
I usually use spray on shellac then a light sanding and then Polly. It stabilizes the material and keeps it clean.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: Finish for woodworking jigs & fixtures?
The only Watco Danish oil I know of and use just has ‘Danish Oil’ on the front. Not sure of varieties of any Watco Danish oil, but a quart lasts me a long time and I think the last I bought was four or five years ago. It cures very hard and adds very little surface depth if you are concerned with tight tolerances. Some have complained that it has flaked, but I’ve never had any flake, though I did have a minwax wipeon poly, flake after a couple of years. I’d attribute that to operator application error before blaming the product.BuckeyeDennis wrote:Sehast mentioned Watco as well. Are you guys talking about their "Danish Oil" products? I see that the Watco brand includes a bunch of different products, including tung oil and wipe-on poly.masonsailor2 wrote:I use Watco when I do seal them but most of the time I just leave them bare.
Paul
https://www.rustoleum.com/product-catal ... nds/watco/
My best results were with a foam brush.
All the jigs I had were coated in Danish oil, but I think that was more out of habit and the oil was on hand.
Not sure any of that helps, but for me, often the old tried and true beats trying new products, though I’m certain there are newer products that offer better results.
Be well,
Ben