Search found 69 matches
- Tue Apr 04, 2023 6:39 pm
- Forum: Maintenance and Repair
- Topic: Jointer disassembly
- Replies: 0
- Views: 225703
Jointer disassembly
Hello fellow Geniuses, I am ready to pull my jointer off and take it apart and clean it. I just received my new knives from SS today. Russ has been helping me but I can’t locate the drawings/diagrams/instructions he referred me to. I am also dealing with a nasty brain issue that is resulting in extr...
- Wed Sep 08, 2021 11:05 pm
- Forum: Maintenance and Repair
- Topic: Turning Bowls in a Wheelchair/Powerchair
- Replies: 10
- Views: 2417
Re: Turning Bowls in a Wheelchair/Powerchair
You are correct. I stated it wrong thank you. It’s the leg that keeps me back to far. The tailstock is removed or will be removed when I start hollowing. I went out and sat in my chair staring at the shopsmith. My engineering pals swung by and they are going to think about all this. Where there is a...
- Wed Sep 08, 2021 5:21 pm
- Forum: Maintenance and Repair
- Topic: Turning Bowls in a Wheelchair/Powerchair
- Replies: 10
- Views: 2417
Turning Bowls in a Wheelchair/Powerchair
Fellow SS Genius’s My machine is a 1983 Mark V 500. I am looking for ideas for a problem I have just “run into”. I have been turning spindles for several months now. When I shifted over to turning bowls I discovered that the right leg/stand is quite the obstacle in getting close enough to the tailst...
- Sat Jun 05, 2021 10:44 pm
- Forum: Maintenance and Repair
- Topic: LATHE SPEEDS?
- Replies: 4
- Views: 1436
LATHE SPEEDS?
Fellow Shopsmith Genius’s! As my Shopsmith skills have improved I am now into turning.I have been asking turners what RPM they run their machines at? I am amazed at the differences I heard or read. Some numbers scared me!. What I would like to know is this..... What speed or Letter used when doing s...
- Tue May 11, 2021 4:16 pm
- Forum: Maintenance and Repair
- Topic: Lower Blade Guard Upgrade Kit
- Replies: 2
- Views: 1224
Lower Blade Guard Upgrade Kit
Fellow Shopsmith Genius’s, I now have the SS lower blade upgrade kit installed. Yes I ended up using the provided template sawing a small slice off the TieBar Boss. We now have clearance. The strike was caused by the new plastic deflector provided in the kit. >>>>> My question is this... Is it “OK” ...
- Wed Apr 28, 2021 11:24 pm
- Forum: Maintenance and Repair
- Topic: Mark V 500 Lower Blade Upgrade Kit
- Replies: 5
- Views: 1708
Re: Mark V 500 Lower Blade Upgrade Kit
Thanks for the input I am going to tackle the upgrade as soon as my new dust collector arrives. I have been learning the art of the Shopsmith Lathe. So far, its a lot of fun. Going from Saw then to Jointer then moving to a lathe on the same machine is just too cool. Especially when all of its owners...
- Mon Apr 26, 2021 9:46 pm
- Forum: Maintenance and Repair
- Topic: Mark V 500 Lower Blade Upgrade Kit
- Replies: 5
- Views: 1708
Mark V 500 Lower Blade Upgrade Kit
Fellow Geniuses,
I recently purchased the SS Lower Blade Guard Upgrade kit. Before I even start I thought I would check and see if there are any closely held secrets in putting this together. When I got to “hacksaw” I decided to ask you folks first. Thank You very much.
Thom
Portland
I recently purchased the SS Lower Blade Guard Upgrade kit. Before I even start I thought I would check and see if there are any closely held secrets in putting this together. When I got to “hacksaw” I decided to ask you folks first. Thank You very much.
Thom
Portland
- Sat Mar 27, 2021 6:18 pm
- Forum: Woodworking Tool Review
- Topic: Sanding Disk / Plates
- Replies: 2
- Views: 943
Sanding Disk / Plates
Fellow Shopsmith Genius’s, Before I ruin my arm what is the best way to remove OLD adhesive from the sanding plates. The first one was easy. The second plate has had paper applied on top of other paper. I got the main paper rounds removed but have a ton of old adhesive left behind. Plate one I used ...
- Sat Jan 16, 2021 6:44 pm
- Forum: Woodworking Tool Review
- Topic: Zyliss Vise
- Replies: 83
- Views: 83812
Re: Zyliss Vise
Great review/topic by Dusty! I have an original Zyliss Vice. It was gifted to me two years back in the original box with the instructions, plus a quick review card for on the fly mounting. Here is what I know... Mine was bought in 1979. They were really big at county fairs and that sort of thing. I ...
- Sat Jan 16, 2021 2:42 pm
- Forum: Woodworking Tool Review
- Topic: Lift Assist
- Replies: 16
- Views: 2971
Re: Lift Assist
WHY would I leave it attached??? Because I am in a wheelchair with a severe neurological condition that limits my weight lift ability to about a whopping 15lbs. I am always looking for work arounds so I can do what I want to do with out asking my wife for help. That’s WHY I would leave it attached. ...