Marc,
Nice acquisition! One added benefit is that you now have the feather guard upgrade!
Search found 28 matches
- Wed Nov 24, 2021 1:13 am
- Forum: Maintenance and Repair
- Topic: New (old) Jointer on ShopSmith Power Stand
- Replies: 28
- Views: 4161
- Mon Nov 15, 2021 6:34 pm
- Forum: Maintenance and Repair
- Topic: Jointer Cleanup and Repair
- Replies: 84
- Views: 12757
Re: Jointer Cleanup and Repair
It appears that the knurled threads were machined into the top of the hex shaft. I'm inclined to leave it alone since the guard is working satisfactorily as is. I may upgrade to the feather guard assembly at a later time. Thanks for your comments.
Tony
Tony
- Fri Nov 12, 2021 5:38 pm
- Forum: Maintenance and Repair
- Topic: Jointer Cleanup and Repair
- Replies: 84
- Views: 12757
Re: Jointer Cleanup and Repair
1A2C6B4B-72E3-48F3-BE03-D74B02930751.jpeg 3396292D-287F-45E5-88C8-78EDFDFC8B0F.jpeg I’m now down to the last short strokes to getting my jointer restoration over the finish line. I have one remaining issue to resolve though and that pertains to the cutter head guard. I’ve attached a couple of photo...
- Tue Nov 09, 2021 2:59 pm
- Forum: Maintenance and Repair
- Topic: Jointer Cleanup and Repair
- Replies: 84
- Views: 12757
Re: Jointer Cleanup and Repair
894AF246-0F03-4483-9FEE-A368B9222490.jpeg 1E43C425-E427-467C-A424-9D2098913F94.jpeg Russ and JPG, thank you for your comments. Since I had already purchased the Dust Chute Retro Kit, I installed the safety guards. With the right drill bit and tap the installation was easier than I anticipated. I re...
- Thu Nov 04, 2021 1:01 pm
- Forum: Maintenance and Repair
- Topic: Jointer Cleanup and Repair
- Replies: 84
- Views: 12757
Re: Jointer Cleanup and Repair
Here are a couple of pics showing the restored jointer. I made a couple of test cuts and obtained nice square cuts. I have about 1 1/4” snipe on the trailing edge of the test stock. From my review of the forum thread regarding snipe I must have the blades set too high. Will adjust accordingly and tr...
- Fri Oct 29, 2021 6:37 pm
- Forum: Maintenance and Repair
- Topic: Jointer Cleanup and Repair
- Replies: 84
- Views: 12757
Re: Jointer Cleanup and Repair
Thanks, Marc and Russ. I can't wait to try it out. It's been fun learning about this tool through the restoration process.
- Fri Oct 29, 2021 12:59 am
- Forum: Maintenance and Repair
- Topic: Jointer Cleanup and Repair
- Replies: 84
- Views: 12757
Re: Jointer Cleanup and Repair
1EF42D28-0B56-4FCE-B674-F2D7BB0E8C31.jpeg Here are some progress photos. I followed the cleaning, penetrol, waxing and painting procedures several of you recommended and this is how it turned out. Installed new bearings on the cutter head and sharpened the jointer knives. Marc Jones graciously let ...
- Sun Oct 17, 2021 1:14 pm
- Forum: Maintenance and Repair
- Topic: Jointer Cleanup and Repair
- Replies: 84
- Views: 12757
Re: Jointer Cleanup and Repair
Thanks for the interesting research and comments. I contacted the EBay seller who sold me the jointer and he said when he acquired it he was told the distinctive pattern on the tables was due to “flaking”. This is consistent with the articles describing hand scraping and frosting. I agree with Denni...
- Sat Oct 16, 2021 11:59 pm
- Forum: Maintenance and Repair
- Topic: Jointer Cleanup and Repair
- Replies: 84
- Views: 12757
Re: Jointer Cleanup and Repair
I agree about the unusual pattern on the jointer infeed and outfeed tables. I followed the cleaning steps of using Scotch Brite pads and WD 40 to clean up the tables with some success but the pattern is still there. The tables are now smooth with no visible rust except for the odd "pattern"...
- Fri Oct 15, 2021 9:11 pm
- Forum: Maintenance and Repair
- Topic: Jointer Cleanup and Repair
- Replies: 84
- Views: 12757
Re: Jointer Cleanup and Repair
Ooops! I thought that might happen. I went back and reviewed Marc’s thread on posting pictures. Hope it works this time. JPG and Russ thank you for your comments.