Search found 34643 matches
- Fri Apr 26, 2024 7:09 pm
- Forum: Maintenance and Repair
- Topic: Loose Drive Assembly where Tool Attach
- Replies: 3
- Views: 263
Re: Loose Drive Assembly where Tool Attach
Assuming the 'knurled' collar is attached correctly, the drill chuck is NOT. The set screws should line up. Also potential play is reduced by rocking the item being attached as the set screw is tightened. This centers the set screw at the low point of the shaft flat.
- Tue Apr 23, 2024 10:07 pm
- Forum: General Woodworking
- Topic: Apprenticeship
- Replies: 4
- Views: 708
Re: Apprenticeship
Good Luck finding a youngster interested in that path.
- Tue Apr 23, 2024 10:06 am
- Forum: Maintenance and Repair
- Topic: Double tilt upgrade
- Replies: 12
- Views: 784
Re: Double tilt upgrade
I be guilty of overlooking that obvious detail! ;>{
- Mon Apr 22, 2024 10:15 pm
- Forum: Maintenance and Repair
- Topic: Double tilt upgrade
- Replies: 12
- Views: 784
Re: Double tilt upgrade
The shims are placed against the SIDES of the tubes. The tube clamp exerts outward pressure to the tubes. The final position is determined by a small boss extending out from the outer interior surface of the end casting. The shims essentially make that boss longer. The shims are necessary since his ...
- Mon Apr 22, 2024 10:05 pm
- Forum: Maintenance and Repair
- Topic: removing speed control handle
- Replies: 3
- Views: 5876
Re: removing speed control handle
CAREFULLY pry around the outer edge at multiple locations a smidgen at a time. You may need to simultaneously pry diametrically opposed to prevent cocking.
- Mon Apr 22, 2024 10:01 pm
- Forum: Maintenance and Repair
- Topic: Double tilt upgrade
- Replies: 12
- Views: 784
Re: Double tilt upgrade
You already have 1 7/8" bench tubes. You need 1 3/4" tubes(only size currently available from the mother ship). You WILL need shims to ensure the correct c-c spacing. The bench tubes press against a boss in the end castings that is shorter on your castings than the current version.
- Mon Apr 22, 2024 10:26 am
- Forum: Community
- Topic: I got a new to me mark
- Replies: 8
- Views: 634
Re: I got a new to me mark
Jigsaw = 5" (Pinless) IIRC? Pins are easily removed from coping saw blades.
Shaper router cutters are attached to the quill shaft.
Shaper router cutters are attached to the quill shaft.
- Sun Apr 21, 2024 9:27 pm
- Forum: Maintenance and Repair
- Topic: Double tilt upgrade
- Replies: 12
- Views: 784
Re: Double tilt upgrade
I presume you have either a greenie or an early goldie. ONLY the bench tubes need to be replaced and 1/16" shims to provide correct c-c spacing.. Your tubes are 1 7/8 od.
- Sun Apr 21, 2024 9:23 pm
- Forum: Community
- Topic: I got a new to me mark
- Replies: 8
- Views: 634
Re: I got a new to me mark
I would say the SS9405 indicates an early SS Inc. product made prior to the switch to date 'serial numbering'.
Note the crinkle paint.
Note the crinkle paint.
- Sun Apr 21, 2024 9:19 pm
- Forum: Maintenance and Repair
- Topic: Quill coupler broken - where to source new part?
- Replies: 14
- Views: 775
Re: Quill coupler broken - where to source new part?
The two version shown above are interchangeable for mark 5/V/7.
Mark VII may require the first one.
Mark VII may require the first one.