Search found 82 matches
- Sat Apr 20, 2019 11:55 am
- Forum: General Woodworking
- Topic: Wolverine jig on Shopsmith
- Replies: 5
- Views: 17991
Re: Wolverine jig on Shopsmith
Which of the mandrels are you using for the CBN wheel
- Fri Mar 22, 2019 4:25 pm
- Forum: Woodworking Tool Review
- Topic: plow planes
- Replies: 9
- Views: 26162
Re: plough planes
Find a Stanley 45/55 but you won't regret a new Veritas Plow Plane. The new and improved version has a wide variety of accessory irons that will pretty much cover anything you might want to do that a plow plane is designed for.
Re: New PTWFE
Drawn from details on page 55 1989 edition, click on the URL two components a rail and drawer blade <<https://a360.co/2TysWnx>>. Not sure what the criticism is here. I get it new cover same material but the devil is in the details. Earlier post indicated you can't make this as illustrated in PTWFE. ...
- Fri Feb 15, 2019 7:40 pm
- Forum: General Woodworking
- Topic: Storm windows- need master advice
- Replies: 10
- Views: 28857
Re: Storm windows- need master advice
Actually I think the perfect tool for corner cleanup is a small bullnose plane with the front slipped off which I guess then makes it a chisel plane. When super sharp oh what perfection to cleanup those pesky corners. A marking gauge to mark the 1/16 trim and a few strokes with the bullnose plane fi...
- Mon Feb 11, 2019 2:08 pm
- Forum: General Woodworking
- Topic: Storm windows- need master advice
- Replies: 10
- Views: 28857
Re: Storm windows- need master advice
Easy solution... clamp a straightedge parallel to the edge you need to remove the 1/16 from exactly 1/16" less than the distance from your router base edge to the outside edge of the bit. Stop short of either end and with a sharp chisel trim the remaining small bits. Nothing fancy, nothing expe...
- Mon Feb 04, 2019 7:12 pm
- Forum: Maintenance and Repair
- Topic: Pat on the back for shopsmith
- Replies: 16
- Views: 25238
Re: Pat on the back for shopsmith
Off topic but still related, where did you find the procedure for replacing the locks and for that matter where did you find the remounting instructions for the Power Pro motor. The Power Pro manual has nothing on the lock replacement nor on mounting or remounting of the motor. Nothing in the MarkV ...
- Mon Jan 28, 2019 12:38 pm
- Forum: Woodworking Tool Review
- Topic: First outing with the SO
- Replies: 3
- Views: 12397
Re: First outing with the SO
Go to youtube and pull up videos by Lars Christensen and Fusion 360. Within a very short time you will be flying along. As a longtime Sketchup user I am doing things within Fusion 360 I can't even imagine doing with Sketchup. I am also probably only using 5% of the capabilities within fusion. Here i...
- Sun Dec 09, 2018 8:38 pm
- Forum: Community
- Topic: segmenting jig
- Replies: 14
- Views: 19148
Re: segmenting jig
Try commercial double sided carpet tape. Hot cold damp. Does leave a residue though but cleans up with 3M adhesive remover. Not sure what the material is on the bottom of my Festool 1400 but I always have a tough time taking the tape apart.
- Wed Dec 05, 2018 2:52 pm
- Forum: Community
- Topic: segmenting jig
- Replies: 14
- Views: 19148
Re: segmenting jig
Routing the arc is a snap following Jerry Bennett's video. Pretty easy to drill two quarter inch holes at a precise distance apart on a batten to use as the pivot arm for the router. Takes longer to put a bit in the collet than two pieces of double sided tape to the router base. Drop a 1/4" bol...
- Thu Oct 04, 2018 7:11 pm
- Forum: Maintenance and Repair
- Topic: Power Pro Lifeless
- Replies: 41
- Views: 38434
Re: Power Pro Lifeless
For what it's worth. I just received shipping notice today that an item I ordered back in July from a completely different company, not is any way related to Shopsmith is preparing to ship. I also had and email with a different vendor that informed me his stock was backordered and I would be looking...