phone  (937) 890-5197

Shopsmith Forums

%nbsp;

16 posts 1 2

cadman57 wrote:Why are a number of the links not able to be shown .............. something about "Religion" problem and showing the information is halted ???

This has to be an incorrect situation ............. is it because some of the titles say "Reborn .........."

How crazy is this ???

dave


They should work now.

Post a reply  Reply with quote 

onevw wrote:I got this thickness planer with the cast alum round handle used to adjust the plate. It is hard to turn, I lubed the lead screws with bo-shield a light lubricant usually used for Alum. But is still very hard the turn handle. Not sure how hard this should be. And help will be appreciated.
Thanks RICK



======================
It is probably dust..

I am no expert ,,,,so allow me to just ask a question,,,, when the table moves up and down ,,,,,it slides in a track on the ends,,, could they be full of dust ,,or even rust?

my dad has a planer that adjust the table with a chain when ya turn the crank handle, constant cleaning is a good thing.

good luck



Hobbyman2

---

Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
- General George S. Patton (1885-1945)

Post a reply  Reply with quote 

It should turn quite easily.

I would be suspicious of the elevator(jack screws) sprockets being out of sync with each other. Have you checked the side to side/front to rear alignment to the cross bars?

---

╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E(SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange

Post a reply  Reply with quote 

Good afternoon JPG,
I picked up a shopsmith at the town dump recently. Needed to reverse engineer the power plant lock to get it from moving down the rails. Question, just bought some sanding parts from Shopsmith and a instruction manual but none of the Mark V model 500 or Mark V model 510 pats match my machine.
The red disc has Model ER serial no. ER35189. wish to find a shop manual to learn about the RPM speeds and set ups.
Thank you
Hartley

Post a reply  Reply with quote 

Your turn Everett.

---

╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E(SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange

Post a reply  Reply with quote 

Sorry JPG,

I have been out of the loop on this one.

I would advise them to follow the link at viewtopic.php?p=185690#p185690

Find the My Google Drive link just after the first four PDF's and find the Fully Restored 10E and 10ER manuals under the 10E& 10ER folders. You can download them and find a good bit of other information on the 10E and 10ER's.

Post a reply  Reply with quote 

Who is online

Users browsing this forum: Bing [Bot], MSN [Bot] and 54 guests

Board indexDelete all board cookies

Welcome to Shopsmith. Please fill in this form and we'll send you more information and special offers for the Shopsmith MARK 7 and other woodworking topics.

Subscribe to our mailing list

* indicates required