Newowner Informaton
Moderators: HopefulSSer, admin
- JPG
- Platinum Member
- Posts: 34650
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Newowner Informaton
Welcome to this forum for shopsmith aficionados.
Last Edited July 2, 2022
Rule #1 Never ever ever turn the speed control dial unless the the shafts are rotating either by manual or motor power.
Rule #2 Lubricate the sheaves often. #10 Machine oil - Turbine oil - 3 in one oil - Sewing machine oil . . .
Rule #3 Use Johnson's ORIGINAL paste wax to both prevent rust and to make things slide easier. JPW is no longer available. Alternatives are Trewax, MinWax finishing wax.
Rule #4 Always lock the carriage and headstock prior to raising to vertical!
Rule #5 Always check all locks before starting any operation. There are either 5 or 4 of them depending on the operation.
Rule #5a When tightening an arbor onto the quill shaft, rock the arbor to insure the set screw is centered over the tapered flat. That prevents subsequent loosening.(added 2016)
Suggestion #1 Watch session # 11 followed by sessions 21 through 24 of the saw dust sessions linked to here
Suggestion #2 Watch the 'premiere' session on table alignment. Gauge not required, just more exacting!!!
Suggested printable download #1 http://www.shopsmith.com/ownersite/productmanuals/MKVMaintenance_1_10.pdf
Suggested printable download #2 http://www.shopsmith.com/ownersite/productmanuals/MKVSTDPartsList%20_1_14.pdf
These downloads are of a 520 model, but other than the table, fence, fence rails and minor differences to the headstock, is the same as other Mark 5/V models.
Do not hesitate to ask questions. There are some good people here and are willing to share their knowledge and experience. There are no dumb/stupid/ridiculous/asinine questions. We have all at one time or more been there done that and can empathize with your confusion. Do not be bashful!
And for more from the mothership - http://www.shopsmith.com/ownersite/star ... signup.htm (new 2015)
Check post #5, this thread! Good Job Dalton!!! viewtopic.php?p=85291#p85291
Check #6 also! Ditto Dalton! viewtopic.php?p=87637#p87637
Another great post - https://www.shopsmith.com/ss_forum/view ... 90#p185690 Fix for a very common problem and it tells how to avoid the problem. (added 2016)
More good reference reading* - https://www.shopsmith.com/ss_forum/view ... 90#p185690
And* * Thanks to Everett! (Mar 2017)
And now a very useful link.
http://www.lhdigest.com/SS/PDFsearch.cfm
Manuals and other stuff.
Last Edited July 2, 2022
Rule #1 Never ever ever turn the speed control dial unless the the shafts are rotating either by manual or motor power.
Rule #2 Lubricate the sheaves often. #10 Machine oil - Turbine oil - 3 in one oil - Sewing machine oil . . .
Rule #3 Use Johnson's ORIGINAL paste wax to both prevent rust and to make things slide easier. JPW is no longer available. Alternatives are Trewax, MinWax finishing wax.
Rule #4 Always lock the carriage and headstock prior to raising to vertical!
Rule #5 Always check all locks before starting any operation. There are either 5 or 4 of them depending on the operation.
Rule #5a When tightening an arbor onto the quill shaft, rock the arbor to insure the set screw is centered over the tapered flat. That prevents subsequent loosening.(added 2016)
Suggestion #1 Watch session # 11 followed by sessions 21 through 24 of the saw dust sessions linked to here
Suggestion #2 Watch the 'premiere' session on table alignment. Gauge not required, just more exacting!!!
Suggested printable download #1 http://www.shopsmith.com/ownersite/productmanuals/MKVMaintenance_1_10.pdf
Suggested printable download #2 http://www.shopsmith.com/ownersite/productmanuals/MKVSTDPartsList%20_1_14.pdf
These downloads are of a 520 model, but other than the table, fence, fence rails and minor differences to the headstock, is the same as other Mark 5/V models.
Do not hesitate to ask questions. There are some good people here and are willing to share their knowledge and experience. There are no dumb/stupid/ridiculous/asinine questions. We have all at one time or more been there done that and can empathize with your confusion. Do not be bashful!
And for more from the mothership - http://www.shopsmith.com/ownersite/star ... signup.htm (new 2015)
Check post #5, this thread! Good Job Dalton!!! viewtopic.php?p=85291#p85291
Check #6 also! Ditto Dalton! viewtopic.php?p=87637#p87637
Another great post - https://www.shopsmith.com/ss_forum/view ... 90#p185690 Fix for a very common problem and it tells how to avoid the problem. (added 2016)
More good reference reading* - https://www.shopsmith.com/ss_forum/view ... 90#p185690
And* * Thanks to Everett! (Mar 2017)
And now a very useful link.
http://www.lhdigest.com/SS/PDFsearch.cfm
Manuals and other stuff.
Last edited by JPG on Fri Mar 24, 2017 7:00 pm, edited 7 times in total.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
- terrydowning
- Platinum Member
- Posts: 1678
- Joined: Mon Jul 19, 2010 3:26 pm
- Location: Windsor, CO
So guilty of violating this one this weekend. Fortunately I only wasted the cutoff and not the production piece (which got steadily wider in a nice taper effect).JPG40504 wrote:Welcome to this forum for shopsmith aficionados.
Rule #5 Always check all locks before starting any operation. There are either 5 or 4 of them depending on the operation.
--
Terry
Copy and paste the URLs into your browser if you want to see the photos.
1955 Shopsmith Mark 5 S/N 296860 Workshop and Tools
https://1drv.ms/i/s!AmpX5k8IhN7ahFCo9VvTDsCpoV_g
Public Photos of Projects
http://sdrv.ms/MaXNLX
Terry
Copy and paste the URLs into your browser if you want to see the photos.
1955 Shopsmith Mark 5 S/N 296860 Workshop and Tools
https://1drv.ms/i/s!AmpX5k8IhN7ahFCo9VvTDsCpoV_g
Public Photos of Projects
http://sdrv.ms/MaXNLX
-
- Gold Member
- Posts: 222
- Joined: Wed Feb 25, 2009 9:51 pm
- Location: White Plains, NY
Suggestion: I like to go "around the clock" on the 5-point check: Carriage lock, Table height lock, Headstock lock, Quill lock, Table tilt lock. By always following this routine, I don't miss anything.JPG40504 wrote: Rule #5 Always check all locks before starting any operation. There are either 5 or 4 of them depending on the operation.
Michael
Mark V Model 500 (1985) upgraded to 520 (2009) and PowerPro (2011); Bandsaw, Jointer, Jigsaw, Planer.
Mark V Model 500 (1985) upgraded to 520 (2009) and PowerPro (2011); Bandsaw, Jointer, Jigsaw, Planer.
- navybeansae
- Bronze Member
- Posts: 6
- Joined: Mon Feb 14, 2011 10:03 pm
- Location: Maryland
A few good links:
1. First, mickyd's catalog of repair discussions on this forum. This is my toolbar bookmark for accessing the forum. The Sawdust Sessions are the second bullet and walk you through cleaning and lubricating of the headstock as well as rebuilding it. Be sure to check out the useful documents uploaded to the blackboard. Also, Mike's restorationthreads listed there answer a lot of basic questions about the process.
2. Ebay is a great place for replacement parts on the classic machines and you can sometimes get them new from Shopsmith, Inc. for about the same price.
3. If your machine didn't come with a copy of "Power Tool Woodworking for Everyone" I highly recommend it, as it has much how-to information in it and a lot of great ideas for jigs and homemade accessories, also available on the Shopsmith website in hard copy and digital version. Other literature you may need is a manual, which is available from Shopsmith in hard copy or you can download digital copies from the 1950's here.
4. Here's Nick Engler's disassembly and cleaning instructions.
5. Shopsmith Most Common Problems and Remedies
6. Exploded diagrams with the parts lists are available on Shopsmith's Service and Repair Parts Index so you will know where to get parts and the applicable terminology for discussing them.
8. The All-In-One Wood Tools site has a list of repair and replacement instructions. Also helpful is JPG's illustrated assembly instructions (still a work in progress).
7. Instructions for posting photos. Post lots!
Lastly, the "search" function on this forum is a powerful tool for finding help when you need it. Just be sure to enter words with four letters or more.
All the best.
1. First, mickyd's catalog of repair discussions on this forum. This is my toolbar bookmark for accessing the forum. The Sawdust Sessions are the second bullet and walk you through cleaning and lubricating of the headstock as well as rebuilding it. Be sure to check out the useful documents uploaded to the blackboard. Also, Mike's restorationthreads listed there answer a lot of basic questions about the process.
2. Ebay is a great place for replacement parts on the classic machines and you can sometimes get them new from Shopsmith, Inc. for about the same price.
3. If your machine didn't come with a copy of "Power Tool Woodworking for Everyone" I highly recommend it, as it has much how-to information in it and a lot of great ideas for jigs and homemade accessories, also available on the Shopsmith website in hard copy and digital version. Other literature you may need is a manual, which is available from Shopsmith in hard copy or you can download digital copies from the 1950's here.
4. Here's Nick Engler's disassembly and cleaning instructions.
5. Shopsmith Most Common Problems and Remedies
6. Exploded diagrams with the parts lists are available on Shopsmith's Service and Repair Parts Index so you will know where to get parts and the applicable terminology for discussing them.
8. The All-In-One Wood Tools site has a list of repair and replacement instructions. Also helpful is JPG's illustrated assembly instructions (still a work in progress).
7. Instructions for posting photos. Post lots!
Lastly, the "search" function on this forum is a powerful tool for finding help when you need it. Just be sure to enter words with four letters or more.
All the best.
Thank you ..
Mobile Storage units@http://www.smartboxusa.com/hampton-roads-moving-storage
storage hampton@http://smartboxusa.com/hampton-roads-moving-storage.php
storage hampton@http://smartboxusa.com/hampton-roads-moving-storage.php
So ya bought one. Now HOW do ya get it home.
http://www.shopsmith.net/forums/showpost.htm?p=85569&postcount=18
http://www.shopsmith.net/forums/showpost.htm?p=85569&postcount=18
Last edited by beeg on Sat Sep 12, 2015 10:48 am, edited 1 time in total.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
- JPG
- Platinum Member
- Posts: 34650
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Top post additions
FYI the top post on this thread has been edited to include links to the online manual and parts list that Dusty provided in another thread. It was suggested by Iv2wdwvk that they be added to the thread.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange