Can anyone tell me of a supplier for the hardware for rolling pin handles? I have looked on the web, but can not find any place that carries just the hardware. Any help would be great.
Dennis
Rolling pin handles
Moderators: HopefulSSer, admin
- a1gutterman
- Platinum Member
- Posts: 3653
- Joined: Tue Jan 09, 2007 12:45 am
- Location: "close to" Seattle
Hi Dennis,
I did a Google search for "rolling pin hardware" and got many results, but nothing actually for any hardware to assemble rolling pins. Then I tried a Google search for "rolling pin parts" and, again got many results, including this one: http://www.svwoodturners.org/Handouts/rollingpin.pdf , and this one: http://www.turnedtreasures.com/galleries/new_turnings/pin_parts3.html , and this was interesting too: http://www.enotes.com/how-products-encyclopedia/rolling-pin . I do knot know if this helps any, but it might give you some ideas.
I did a Google search for "rolling pin hardware" and got many results, but nothing actually for any hardware to assemble rolling pins. Then I tried a Google search for "rolling pin parts" and, again got many results, including this one: http://www.svwoodturners.org/Handouts/rollingpin.pdf , and this one: http://www.turnedtreasures.com/galleries/new_turnings/pin_parts3.html , and this was interesting too: http://www.enotes.com/how-products-encyclopedia/rolling-pin . I do knot know if this helps any, but it might give you some ideas.
Tim
Buying US made products will help keep YOUR job or retirement funds safer.
Buying US made products will help keep YOUR job or retirement funds safer.
http://www.svwoodturners.org/Handouts/rollingpin.pdf
This one from A1 show you how to make a rolling pin, you just need the wood for it.
This one from A1 show you how to make a rolling pin, you just need the wood for it.
Last edited by beeg on Thu Dec 21, 2017 3:56 pm, edited 1 time in total.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
- tom_k/mo
- Platinum Member
- Posts: 856
- Joined: Mon Jul 14, 2008 3:58 pm
- Location: St. Louis, MO
- Contact:
Wish I could find a source for marble rolling pin rollers... I use quite a number of them in my sandcarving and I'm sure I could make the rest of the parts and assemble cheaper than purchasing & shipping... They make a nice kitchen decoration with the family name carved in them. Here'swhat they look like.
ShopSmith MarkV-520 with Belt Sander, Jointer, Band Saw, Strip Sander, Scroll Saw and Biscuit Jointer SPTs and a DC-3300...
Woodworking Hobbyist (Check out all my Woodworking Plans (http://vbwhiz.isa-geek.net/plans)
Aspiring Sandcarver: Breaking glass one grain at a time.
Black Powder Shooter (love the smell of burning sulfur).
Woodworking Hobbyist (Check out all my Woodworking Plans (http://vbwhiz.isa-geek.net/plans)
Aspiring Sandcarver: Breaking glass one grain at a time.
Black Powder Shooter (love the smell of burning sulfur).
-
- Gold Member
- Posts: 75
- Joined: Mon Feb 18, 2008 6:03 pm
- Location: Auckland, New Zealand
- Contact:
A couple of years back I turned several rolling pins complete with handles attached (fixed) in place. These were christmas gifts that were well recieved and are in constant use.
I got a rough overall cylinder shape and used the 12 inch sanding disk with 100 grit paper and held over the top of the cylinder and it did a great job of smoothing off the rolling pin. I followd through up to 320 grit.
The handles were an exercise in using a skew chisel and if both handles were not quite exact, that did not matter too much as it gave the rolling pin that hand made look and feel.
The wood was basic hard wood - oak I think.
Finished with organ oil hi-speed finishing oil
Give it a go and surprise yourself - great fun and a learning experience.
Regards
Sandy in NZ
I got a rough overall cylinder shape and used the 12 inch sanding disk with 100 grit paper and held over the top of the cylinder and it did a great job of smoothing off the rolling pin. I followd through up to 320 grit.
The handles were an exercise in using a skew chisel and if both handles were not quite exact, that did not matter too much as it gave the rolling pin that hand made look and feel.
The wood was basic hard wood - oak I think.
Finished with organ oil hi-speed finishing oil
Give it a go and surprise yourself - great fun and a learning experience.
Regards
Sandy in NZ
1960 SS500, Magna Jointer & Dado. Hailing from New Zealand
- dusty
- Platinum Member
- Posts: 21359
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Rolling pin handles
This guy sure went back in time to resurrect this post.
SCAM ALL THE WAY. He is now an addition to my Foe List.
SCAM ALL THE WAY. He is now an addition to my Foe List.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.