Search found 77 matches
- Tue Jul 27, 2010 10:15 pm
- Forum: Woodworking Tool Review
- Topic: for the new Mark VII
- Replies: 9
- Views: 4917
for the new Mark VII
I have a suggestion for Shopsmith and hope the rest of you will chip in. For many years I've used a 10ER and then lately I acquired a Mark VII. Fortunately most of the gear rack is usable. I hope if a new Mark VII is built and a steel (not plastic) gear rack will be part of it. If one wants to raise...
- Sun Jul 18, 2010 9:39 pm
- Forum: Maintenance and Repair
- Topic: old Mark VII
- Replies: 3
- Views: 2840
old Mark VII
This must start as a gloat. I picked up a Mark VII this weekend for the vast sum of $40. It had sat for sixteen years after the owner past away. His widow was moving to a condo and had to sell it off. I did run it for a second and I turned the speed control just a little way. Turning it back down I ...
- Fri Jun 18, 2010 10:18 pm
- Forum: General Woodworking
- Topic: Tool Features that frustrate me
- Replies: 29
- Views: 7409
Reply to Ed and "soft" punches
Hard steel punches would shatter when struck by the hard steel of a hammer face. So unless you would only use a mallet you definitely would not want a hard punch. I didn't believe in hard steel shattering until I was helping my boss drive out a bearing race. He was using an aluminum punch on this ve...
- Wed Apr 14, 2010 10:07 pm
- Forum: Maintenance and Repair
- Topic: Extra Parts need id help
- Replies: 6
- Views: 3761
I may be stating what is already known
The parts are for the 10E or 10ER. The Yahoo group for 10ER has files that will identify most of them.
Ed
Ed
- Thu Mar 18, 2010 8:48 pm
- Forum: Maintenance and Repair
- Topic: 10 E Question(s)
- Replies: 41
- Views: 20733
Lots of luck
You may not be very successful in drilling out a roll pin. Roll pins are made from spring steel and are VERY hard. They often are harder than drill bits and so the drill goes dull long before you make any progress. Frozen roll pins are a big problem even for machinists. Do a lot soaking (PB Blaster)...
- Fri Jan 29, 2010 9:32 pm
- Forum: Beginning Woodworking
- Topic: Murphy Bed ?
- Replies: 4
- Views: 2969
- Mon Jan 25, 2010 9:47 pm
- Forum: General Woodworking
- Topic: Another thought about Norm & NYW
- Replies: 5
- Views: 2336
Another thought about Norm & NYW
Watching the web site's repeat of early episodes I was struck by what was the original appeal to the series. Norm used equipment that I might have. He didn't have a mortising machine. He had a Shopsmith bandsaw and so on. I think it was in the last season Norm was re-sawing some material. The bandsa...
- Fri Jan 08, 2010 10:09 pm
- Forum: Woodworking Tool Review
- Topic: The Whirlwind Braking System
- Replies: 36
- Views: 19380
stopping a saw blade
I used to work in a place where we used a 7-1/2 HP Dewalt radial saw to cut aluminum extrusions. It originally had a brake system that was engaged by a solenoid to stop the blade. The aluminum saw dust shorted it out in no time flat. For a long time we didn't have a brake and it took a LONG time to ...
- Fri Jan 08, 2010 9:42 pm
- Forum: Woodworking Tool Review
- Topic: New Yankee Workshop online
- Replies: 6
- Views: 6099
What about the band saw?
Wasn't that an SPT bandsaw that he used in this video also?
Ed Friedl
Ed Friedl
- Thu Dec 10, 2009 1:28 pm
- Forum: General Woodworking
- Topic: keeping one's eyes open
- Replies: 0
- Views: 1589
keeping one's eyes open
It always amazes me how buried treasures can be found in unusual places. Our church had a grand piano in the choir rehearsal room. It wasn't the best sounding and it looked like a refugee from the scrap heap. Some naughty person managed to spill soda into the interior. And it really gummed up the wo...